Description
ThinkDiag 2 has Powerful and Competitive Features:
The same comprehensive functions as thousands of dollars valued diagnostic tools but at a much lower price Diagnostic Functions.
Thinkdiag 2 Supports Full 10 OBD2 Diagnostic Functions :
- Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)
- Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.
- Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
- I/M Readiness Status: This shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
- Read Live Data Stream: Show the information of continuous data stream from a vehicle in a live graphic (waveform) display.
- View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the onboard computer at the time the emission-related fault occurs.
- O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s onboard computer.
- On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
- Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
- Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability
Thinkdiag 2 Supports 16 maintenance functions to meet the maintenance vehicle repair and after-sales maintenance:
- Oil Reset Service
The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle.-
- Steering Angle Calibration
To reset the steering angle, first find the relative zero point position for the car to drive in a straight line. Taking this position as a reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle. - Electronic Parking Brake Reset
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. Otherwise, the car alarms.
- Battery Register & Battery Maintenance
This function enables you to perform a resetting operation on the monitoring unit of the vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.
- ABS Bleeding
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. lf the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.
- Electronic Throttle Position Reset & Learn
Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state. By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjusting the intake volume.
- Diesel Particulate Filter (DPF) Regeneration
DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high-temperature heating combustion, fuel additive or catalyst to reduce PM ignition combustion) to stabilize the filter performance.
- – Tire Pressure Monitor System Reset
After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting function must be performed to reset tire pressure and turn off the tire pressure MIL. Tire pressure resetting must be performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tire pressure monitoring device is replaced or installed, the tire is replaced, the tire pressure sensor is damaged, and tire is replaced for the car with tire pressure monitoring function.
- Gear Learning
The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computer to more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped with a Delphi engine, the MlL turns on after the engine is started. The diagnostic device detects the DTC P1336’gear not learned’. In this case, you must use the diagnostic device to perform gear learning for the car. After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, crankshaft flywheel is replaced, or the DTC ‘gear not learned” is present, gear learning must be performed.
- Anti-theft ( IMMO ) Matching
To prevent the car from being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery is replaced, anti-theft key matching must be performed.
- Injector matching
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, the injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identify injectors to accurately control fuel injection.
- Air Suspension Reset
This function can adjust the height of the body. When replacing the body height sensor in the air suspension system, or control module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration.
- Gearbox /Transmission Reset
This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox is disassembled or repaired (after some of the car battery is powered off), it will lead to shifting delay or impact problems. In this case, this function needs to be done so that the gearbox can automatically compensate according to the driving conditions so as to achieve more comfortable and better shift quality.
- Sunroof RESET
This function can set the sunroof lock off, closed it when it rains, slide/tilt the sunroof memory function, temperature threshold outside the car etc.
- AFS Reset (EGR)
This feature is used to initialize the adaptive headlamp system. According to the ambient light intensity, the adaptive headlamp system may decide whether to automatically turn on the headlamps and timely adjust the headlamp lighting angle while monitoring the vehicle speed and body posture.
- EGR Reset
Thinkcar ThinkDiag 2 Full system OBDII Code Reader with 16 reset functions for Android/IOS phone with 1 Year software Free Update.
Specifications:
Support system: Android, IOS
Bluetooth: hardware supports 5.0BLE, Bluetooth dual mode
Diagnostic interface: DB15
Working voltage: 12V
What’s in the box
1 x Thinkdiag 2 with OBD2 cable
1 x Manual book